Contact The Titanium Processing Center for all of your Titanium and Titanium Alloys needs

COMMERCIALLY PURE TITANIUM

TITANIUM GRADE GR.1         Gr.2     Gr.3     Gr.4     Gr.7
Chemical Composition (%)
(Max. values unless range is shown)		 0.08 C; 0.20 FE*, 0.03 N; 0.18 O; 0.015 H
(sheet; 0.0125H (bar); 0.00100 H (billet)
MILL ANNEALED
TENSILE PROPERTIES		 Guar. R.T. Min. Typical Elev. Temp. Prop.
600 F800 F1000 F
Ultimate Strength (psi) 35,000 26,000 20,000
Yield Strength (psi)0.2% offset 25,000 15,000 13,000
Elongation in 2" (%)
Sheet > 0.025 thick		 24 32 26
Reduction in Area (%) Bar 30 70/80 70/80
MECHANICAL PROPERTIES *Also available with 0.05 max FE for superior corrosion resistance.
Stress Rupture
in Time Shown		 Stress (psi)
Time (Hrs.)
Stress and Time
to Produce Elongation
Shown (Creep)		 Stress (psi)
Time (Hrs.)
Creep (%)
Charpy V-Notch Impact (ft.-lbs.) at Room Temperature
Bend Radius Under 0.070" thick 1.5 X Thickness
0.070" And Over 2.0 X Thickness
Welded Bend Radius 1.5 - 2.0 X Thickness
Hardness RΒ70
PHYSICAL PROPERTIES
Beta Transus (F ± 25) 1630
Coefficient of Thermal Expansion (10-6in./in./F) 32-212 4.8
32-600 5.1
32-1000 5.4
32-1200 5.6
32-1500 5.6
Density (lbs./cu. in.) 0.163
Melting Point, Approx (F) 3040
Electrical Resistivity at Room Temp. (Microhms cm) 56
Modulus Elasticity - Tension (106 psi) 14.9
Modulus Elasticity - Torsion (106 psi) 6.5
Thermal Conductivity
(Btu/hr/sq. ft./F/ft.)		 9.0 at Room Temperature
Specific Heat (Btu/lb./F) at Room Temp. 0.124
Weldability Good
Annealing Temp. (F) Full 1300°/30 Min. - 2 Hrs,; Air Cool
Stress Relief 1000-1100°/30 Min.; Air Cool
Forging* Temp. (F) Blocking 1600-1700°
Finishing 1500-1600°
Available Mill Products Bar, Billet, Extrusions, Plate Sheet, Strip, Wire, Pipe, Tubing
Typical Application For corrosion resistance in the chemical and marine industries; in air-frame construction where maximum ease of formability is desired.
Industry Specifications ASTM
  • B265 Grade 1
  • B348 Grade 1
  • B337 Grade 1
  • B338 Grade 1
  • F67 Grade 1
  • F467 Grade 1
  • F468 Grade 1
TITANIUM GRADE GR.1     Gr.2     Gr.3     Gr.4     Gr.7     top        
Chemical Composition (%)
(Max. values unless range is shown)		 0.08 C; 0.25 FE*, 0.03 N; 0.20 O; 0.015 H
(sheet; 0.0125H (bar); 0.00100 H (billet)
MILL ANNEALED
TENSILE PROPERTIES		 Guar. R.T. Min. Typical Elev. Temp. Prop.
600 F 800 F 1000 F
Ultimate Strength (psi) 50,000 30,000 26,000 19,000
Yield Strength (psi)0.2% offset 40,000 18,000 15,000 11,000
Elongation in 2" (%)
Sheet > 0.025 thick		 20 37 25 32
Reduction in Area (%) Bar 20 70/80 70/80 70/80
MECHANICAL PROPERTIES *Also available with 0.05 max FE for superior corrosion resistance.
Stress Rupture
in Time Shown		 Stress (psi)
Time (Hrs.)
Stress and Time
to Produce Elongation
Shown (Creep)		 Stress (psi)
Time (Hrs.)
Creep (%)
Charpy V-Notch Impact (ft.-lbs.) at Room Temperature 25-40
Bend Radius Under 0.070" thick 1.5 X Thickness
0.070" And Over 2.0 X Thickness
Welded Bend Radius 2.0 - 3.0 X Thickness
Hardness RΒ70
PHYSICAL PROPERTIES
Beta Transus (F ± 25) 1675
Coefficient of Thermal Expansion (10-6in./in./F) 32-212 4.8
32-600 5.1
32-1000 5.4
32-1200 5.6
32-1500 5.6
Density (lbs./cu. in.) 0.163
Melting Point, Approx (F) 3020
Electrical Resistivity at Room Temp. (Microhms cm) 56
Modulus Elasticity - Tension (106 psi) 14.9
Modulus Elasticity - Torsion (106 psi) 6.5
Thermal Conductivity
(Btu/hr/sq. ft./F/ft.)		 9.5 at Room Temperature
Specific Heat (Btu/lb./F) at Room Temp. 0.124
Weldability Good
Annealing Temp. (F) Full 1300°/30 Min. - 2 Hrs,; Air Cool
Stress Relief 1000-1100°/30 Min.; Air Cool
Forging* Temp. (F) Blocking 1600-1700°
Finishing 1500-1600°
Available Mill Products Bar, Billet, Extrusions, Plate Sheet, Strip, Wire, Pipe, Tubing
Typical Application For corrosion resistance in the chemical and marine industries; in aircraft construction where higher strength level and ease of formability is desired.
Industry Specifications ASTM
  • B265 Grade 2
  • B348 Grade 2
  • B467 Grade 2
  • B468 Grade 2
  • B861 Grade 2
  • B862 Grade 2
  • F337 Grade 2
  • F338 Grade 2
  • F67 Grade 2
TITANIUM GRADE GR.1     Gr.2     Gr.3     Gr.4     Gr.7     top        
Chemical Composition (%)
(Max. values unless range is shown)		 0.08 C; 0.25 FE*, 0.05 N; 0.30 O; 0.015 H
(sheet; 0.0125H (bar); 0.00100 H (billet)
MILL ANNEALED
TENSILE PROPERTIES		 Guar. R.T. Min. Typical Elev. Temp. Prop.
600 F 800 F 1000 F
Ultimate Strength (psi) 65,000 32,000 29,000 22,000
Yield Strength (psi)0.2% offset 55,000 20,000 17,000 13,000
Elongation in 2" (%)
Sheet > 0.025 thick		 18 35 18 33
Reduction in Area (%) Bar 30 70/80 70/80 70/80
TITANIUM MECHANICAL PROPERTIES *Also available with 0.05 max FE for superior corrosion resistance.
Stress Rupture
in Time Shown		 Stress (psi)   20,000  
Time (Hrs.)   100  
Stress and Time
to Produce Elongation
Shown (Creep)		 Stress (psi)
Time (Hrs.)
Creep (%)
Charpy V-Notch Impact (ft.-lbs.) at Room Temperature 20-40
Bend Radius Under 0.070" thick 2.0 X Thickness
0.070" And Over 2.5 X Thickness
Welded Bend Radius 2.0 - 3.0 X Thickness
Hardness RΒ90
TITANIUM PHYSICAL PROPERTIES
Beta Transus (F ± 25) 1690
Coefficient of Thermal Expansion (10-6in./in./F) 32-212 4.8
32-600 5.1
32-1000 5.4
32-1200 5.6
32-1500 5.6
Density (lbs./cu. in.) 0.163
Melting Point, Approx (F) 3020
Electrical Resistivity at Room Temp. (Microhms cm) 56
Modulus Elasticity - Tension (106 psi) 15.0
Modulus Elasticity - Torsion (106 psi) 6.5
Thermal Conductivity
(Btu/hr/sq. ft./F/ft.)		 9.5 at Room Temperature
Specific Heat (Btu/lb./F) at Room Temp. 0.124
Weldability Good
Annealing Temp. (F) Full 1300°/30 Min. - 2 Hrs,; Air Cool
Stress Relief 1000-1100°/30 Min.; Air Cool
Forging* Temp. (F) Blocking 1600-1700°
Finishing 1500-1600°
Available Mill Products Bar, Billet, Extrusions, Plate Sheet, Strip, Wire, Pipe, Tubing
Typical Application For corrosion resistance in the chemical and marine industries;for aircraft construction.
Industry Specifications ASTM
  • B265 Grade 3
  • B348 Grade 3
  • B337 Grade 3
  • B338 Grade 3
  • F67 Grade 3
GRADE GR.1     Gr.2     Gr.3     Gr.4     Gr.7     top        
Chemical Composition (%)
(Max. values unless range is shown)		 0.08 C; 0.50 FE*, 0.05 N; 0.40 O; 0.015 H
(sheet; 0.0125H (bar); 0.00100 H (billet)
MILL ANNEALED
TENSILE PROPERTIES		 Guar. R.T. Min. Typical Elev. Temp. Prop.
600 F 800 F 1000 F
Ultimate Strength (psi) 80,000 44,000 34,000 27,000
Yield Strength (psi)0.2% offset 70,000 24,000 21,000 16,000
Elongation in 2" (%)
Sheet > 0.025 thick		 15 18 22 29
Reduction in Area (%) Bar 25 70/80 70/80 70/80
MECHANICAL PROPERTIES *Also available with 0.05 max FE for superior corrosion resistance.
Stress Rupture
in Time Shown		 Stress (psi) 17,000
Time (Hrs.) 450
Stress and Time
to Produce Elongation
Shown (Creep)		 Stress (psi) 8,000
Time (Hrs.) 150
Creep (%) .15
Charpy V-Notch Impact (ft.-lbs.) at Room Temperature
Bend Radius Under 0.070" thick 2.5 X Thickness
0.070" And Over 3.0 X Thickness
Welded Bend Radius 3.0 - 5.0 X Thickness
Hardness RΒ100
PHYSICAL PROPERTIES
Beta Transus (F ± 25) 1740
Coefficient of Thermal Expansion (10-6in./in./F) 32-212 4.8
32-600 5.1
32-1000 5.4
32-1200 5.6
32-1500 5.6
Density (lbs./cu. in.) 0.163
Melting Point, Approx (F) 3020
Electrical Resistivity at Room Temp. (Microhms cm) 60
Modulus Elasticity - Tension (106 psi) 15.1
Modulus Elasticity - Torsion (106 psi) 6.5
Thermal Conductivity
(Btu/hr/sq. ft./F/ft.)		 9.8 at Room Temperature
Specific Heat (Btu/lb./F) at Room Temp. 0.129
Weldability Good
Annealing Temp. (F) Full 1300°/30 Min. - 2 Hrs,; Air Cool
Stress Relief 1000-1100°/30 Min.; Air Cool
Forging* Temp. (F) Blocking 1600-1700°
Finishing 1500-1600°
Available Mill Products Bar, Billet, Extrusions, Plate Sheet, Strip, Wire, Pipe, Tubing
Typical Application For corrosion resistance in the chemical and marine industries;for aircraft construction.
Industry Specifications ASTM
  • B265 Grade 4
  • B348 Grade 4
  • F67 Grade 4
  • F467 Grade 4
  • F468 Grade 4
TITANIUM GRADE GR.1     Gr.2     Gr.3     Gr.4     Gr.7     top        
Chemical Composition (%)
(Max. values unless range is shown)		 0.08 C; 0.30 FE*, 0.03 N; 0.2 Pd; 0.020 O
0.015 H (sheet); 0.0125H (bar)
MILL ANNEALED
TENSILE PROPERTIES		 Guar. R.T. Min. Typical Elev. Temp. Prop.
600 F 800 F 1000 F
Ultimate Strength (psi) 50,000 30,000 26,000 19,000
Yield Strength (psi)0.2% offset 40,000 18,000 15,000 11,000
Elongation in 2" (%)
Sheet > 0.025 thick		 20 37 25 32
Reduction in Area (%) Bar 25 70/80 70/80 70/80
MECHANICAL PROPERTIES *Also available with 0.05 max FE for superior corrosion resistance.
Stress Rupture
in Time Shown		 Stress (psi)
Time (Hrs.)
Stress and Time
to Produce Elongation
Shown (Creep)		 Stress (psi)
Time (Hrs.)
Creep (%)
Charpy V-Notch Impact (ft.-lbs.) at Room Temperature
Bend Radius Under 0.070" thick 2.0 X Thickness
0.070" And Over 2.5 X Thickness
Welded Bend Radius 2.0 - 3.0 X Thickness
Hardness RΒ80
PHYSICAL PROPERTIES
Beta Transus (F ± 25) 1675
Coefficient of Thermal Expansion (10-6in./in./F) 32-212 4.8
32-600 5.1
32-1000 5.4
32-1200 5.6
32-1500 5.6
Density (lbs./cu. in.) 0.163
Melting Point, Approx (F) 3020
Electrical Resistivity at Room Temp. (Microhms cm) 56
Modulus Elasticity - Tension (106 psi) 14.9
Modulus Elasticity - Torsion (106 psi) 6.5
Thermal Conductivity
(Btu/hr/sq. ft./F/ft.)		 9.5 at Room Temperature
Specific Heat (Btu/lb./F) at Room Temp. 0.124
Weldability Good
Annealing Temp. (F) Full 1300°/30 Min. - 2 Hrs,; Air Cool
Stress Relief 1000-1100°/30 Min.; Air Cool
Forging* Temp. (F) Blocking 1600-1700°
Finishing 1500-1600°
Available Mill Products Bar, Billet, Extrusions, Plate Sheet, Strip, Wire, Pipe, Tubing
Typical Application For corrosion resistance in the chemical industry where media is mildly reducing or varies between oxidizing and reducing.
Industry Specifications ASTM
  • B265 Grade 7
  • B348 Grade 7
  • F337 Grade 7
  • F338 Grade 7
  • F467 Grade 7
  • F468 Grade 7
GR.1     Gr.2     Gr.3     Gr.4     Gr.7     top        
Contact The Titanium Processing Center
Contact The Titanium Processing Center for more info about Commercial Grade titanium

Contact The Titanium Processing Center for all of your commercial grade titanium needs ...more

The Titanium Processing Center accepts Visa, Mastercard, and American Express credit cards
Toll-Free: (888) 771-9449
2000 East Avis Dr.
Madison Heights, MI 48071














eXTReMe Tracker